Honeywell Photo Scanner 1902 User Manual

Xenon™ 1902/1912  
Cordless Area-Imaging Scanner  
Quick Start Guide  
Aller à www.honeywellaidc.com pour le français.  
Vai a www.honeywellaidc.com per l'italiano.  
Gehe zu www.honeywellaidc.com für Deutsch.  
Ir a www.honeywellaidc.com para español.  
Para Português, acesse www.honeywellaidc.com.br.  
Перейти на русскоязычный сайт www.honeywellaidc.com.  
Pro češtinu jdi na www.honeywellaidc.com.  
Pre slovenčinu choď na www.honeywellaidc.com  
查看繁体版请登陆 www.honeywellaidc.com  
한글 www.honeywellaidc.com 로 이동합니다 .  
Crdlss-NG2D-QS Rev D  
8/12  
 
Connecting the Scanner  
USB:  
Keyboard Wedge:  
 
RS232 Serial Port:  
RS485:  
 
Reading Techniques  
The view finder projects an aiming  
beam that should be centered over  
the bar code, but it can be  
positioned in any direction for a  
good read.  
Hold the scanner over the bar code,  
pull the trigger, and center the  
aiming beam on the bar code.  
The aiming beam is smaller when  
the scanner is closer to the code and larger when it is farther from the  
code. Hold the scanner close to smaller bar codes, and farther away  
from large bar codes to get a proper read.  
If the bar code is highly reflective (e.g., laminated), you may need to  
tilt the scanner at an angle so the bar code can be scanned.  
Note: If the scanner beeps 3 times when scanning a bar code, the  
link has not been established. If the scanner beeps once, the  
link has been established.  
Standard Product Defaults  
The following bar code resets all standard product default settings.  
Standard Product Defaults  
 
RS485 Interface  
The RS485 interface defaults to port 5B. If you have an IBM POS  
terminal using port 9B, scan the appropriate code below to program  
the terminal, then power cycle the cash register.  
IBM Port 9B HHBCR-1  
Interface  
IBM Port 9B HHBCR-2  
Interface  
Note: For additional RS485 interface selections, see the User’s  
Guide for your product at our website,  
USB Serial  
Scan the following code to program the scanner to emulate a regular  
RS232-based COM Port. If you are using a Microsoft® Windows®  
PC, you will need to download a driver from the Honeywell website  
(www.honeywellaidc.com). The driver will use the next available  
COM Port number. Apple® Macintosh computers recognize the  
scanner as a USB CDC class device and automatically use a class  
driver.  
USB Serial  
Note: No extra configuration (e.g., baud rate) is necessary.  
 
USB PC Keyboard  
Scan the following code to program the scanner for a USB PC  
Keyboard.  
USB PC Keyboard  
Keyboard Country  
Scan the Program Keyboard Country bar code below, then scan  
the numeric bar code(s) from page 2, then the Save bar code to  
program the keyboard for your country. As a general rule, the  
following characters are not supported by the scanner for countries  
other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~  
Program Keyboard Country  
Country Code  
Belgium  
Scan Country Code  
Scan  
1
8
2
3
4
7
Italy  
5
Denmark  
Norway  
9
Finland  
Spain  
10  
6
France  
Switzerland  
USA (Default)  
Germany/Austria  
Great Britain  
0
Save  
 
Note: For a complete list of country codes, see the User’s Guide for  
Locked Link  
If you link a scanner to a base using the Locked Link Mode, other  
scanners are blocked from being linked if they are inadvertently  
placed into the base. If you do place a different scanner into the  
base, it will charge the scanner, but the scanner will not be linked.  
Locked Link Mode  
(Single Scanner)  
To use a different scanner, you need to unlink the original scanner by  
scanning the Unlink Scanner bar code.  
Override Locked Scanner  
If you need to replace a broken or lost scanner that is linked to a  
base, scan the Override Locked Scanner bar code with a new  
scanner, and place that scanner in the base. The locked link will be  
overridden; the broken or lost scanner’s link with the base will be  
removed, and the new scanner will be linked.  
Override Locked Scanner  
 
Unlinking the Scanner  
If the base has a scanner linked to it, that scanner must be unlinked  
before a new scanner can be linked. Once the previous scanner is  
unlinked, it will no longer communicate with the base. Scan the  
Unlink Scanner bar code to unlink a scanner.  
Unlink Scanner  
Trigger  
The following bar codes will allow you to use the scanner in Manual  
Trigger - Normal Mode (need to press the trigger to read) or  
Presentation mode (the scanner is activated when it “sees” a bar  
code).  
Manual Trigger - Normal  
(Default)  
Presentation Mode  
Streaming Presentation™  
When in Streaming Presentation mode, the scanner leaves the scan  
illumination on all the time and continuously searches for bar codes.  
Streaming Presentation Mode  
 
Suffix  
If you want a carriage return after the bar code, scan the Add CR  
Suffix bar code. To add a tab after the bar code, scan the Add Tab  
Suffix bar code. Otherwise, scan the Remove Suffix bar code to  
remove the suffixes.  
Add CR Suffix  
Add Tab Suffix  
Remove Suffix  
Add Code ID Prefix to all Symbologies  
Scan the following bar code if you wish to add a Code ID prefix to all  
symbologies at once.  
Add Code ID Prefix To All Symbologies  
(Temporary)  
Note: For a complete list of Code IDs, see the User’s Guide for your  
 
Function Code Transmit  
When this selection is enabled and function codes are contained  
within the scanned data, the scanner transmits the function code to  
the terminal. Charts of these function codes are provided in your  
User’s Guide. When the scanner is in keyboard wedge mode, the  
scan code is converted to a key code before it is transmitted.  
Enable  
(Default)  
Disable  
 
Data Format Editor Instructions  
The following are abbreviated instructions for entering a data format.  
For complete instructions refer to your User’s Guide, available at our  
1. Scan the Enter Data Format symbol.  
2. Primary/Alternate Format: scan 0 for Primary Format  
3. Terminal Type: scan 099 for any terminal type  
4. Code I.D.: scan 99 for any bar code type  
5. Length: scan 9999 for any length bar code.  
6. Editor commands: use the Programming Chart that follows.  
7. Scan Save to save your entries.  
Enter Data Format  
Clear All Data Formats  
Save  
 
Programming Chart  
0
2
4
6
1
3
5
7
 
8
9
B
D
F
A
C
E
Save  
 
EZConfig-Scanning  
To access additional features for the scanner use EZConfig-  
Scanning, an online configuration software tool, available from our  
Technical Assistance  
Contact information for technical support, product service, and repair  
can be found at www.honeywellaidc.com.  
Limited Warranty  
product’s warranty information.  
Patents  
For patent information, refer to www.honeywellaidc.com/patents.  
User Documentation  
For localized versions of this document, and to download the User’s  
Guide, go to www.honeywellaidc.com.  
Disclaimer  
Honeywell International Inc. (“HII”) reserves the right to make changes in  
specifications and other information contained in this document without prior  
notice, and the reader should in all cases consult HII to determine whether  
any such changes have been made. The information in this publication does  
not represent a commitment on the part of HII.  
HII shall not be liable for technical or editorial errors or omissions contained  
herein; nor for incidental or consequential damages resulting from the  
furnishing, performance, or use of this material.  
This document contains proprietary information that is protected by copyright.  
All rights are reserved. No part of this document may be photocopied,  
reproduced, or translated into another language without the prior written  
consent of HII.  
© 2011-2012 Honeywell International Inc. All rights reserved.  
 
 

Haan Carpet Cleaner SI 3b User Manual
Haier Flat Panel Television HL15E User Manual
HANNspree Flat Panel Television ST32 15C1 User Manual
Harman Kardon Speaker PC350 User Manual
Hasbro Robotics 6805280000 User Manual
Hotpoint Refrigerator BM10 User Manual
Huawei Cell Phone Y300 User Manual
IBM Computer Drive 61X User Manual
IKEA Landscape Lighting AA 96974 4 User Manual
Impex Fitness Equipment IGS 04 User Manual